Dlink di 624 installation

You will use this MAC address to specify the only computers allowed to connect to your home network. Select the Advanced tab and select Filters in the left pane. Enter a name for the computer you're allowing access to your network in the Name field. You may want to give it a descriptive name like Dad's notebook or Family Room Desktop. Enter the computer's MAC Address. When you have entered the MAC address of each computer that will be connected to your network, select Only allow computers with MAC address listed below to access the network.

Click Apply. Now, only computers included in this list will be allowed to access your home network. If you have additional computers you want to connect to your wireless network, please follow the directions below.

If you have no additional computers to connect, you can skip to Step 6. The instructions for adding a computer to your wireless network depends on whether the computer you're adding has a wireless network adapter already installed.

If your computer has a wireless adapter built in or you have previously installed a wireless network adapter , you only need to set up the connection to the wireless network. The directions are much simpler and generally take less than five minutes to complete. If you're unsure about whether you have a wireless network adapter, you can use Windows Device Manager to determine whether you have one installed. If you don't have a wireless network adapter installed , connecting an additional computer will require two major steps:.

Note : If you're creating a wireless network for a single laptop computer, you can skip this step and continue with Step 6.

Review the advantages that each type of connection provides to determine the best solution for your situation. Connect additional computers by selecting either a completely wireless or a combination network.

The final step is to test your Internet connection on each computer on your home network. This ensures that all the connections are secure, and the hardware configurations are working properly.

What's Next? You have successfully installed your wireless home network. When you're ready, the next step to get the maximum benefits from your home network is to configure Windows to share folders and printers. Note : Many new notebook computers have built-in wireless network cards. Be sure to check your notebook computer to see if it already has a network card.

If you have forgotten your router's user name or password, you must reset the router to the factory settings to access the configuration utility. You can't update any security settings unless you know the user name and password and can access the router's configuration utility.

Your D-Link DI router is now using the default settings for the network configuration. You must re-configure your D-Link router to match the previous settings that were assigned to all the other devices on your wireless network. Otherwise, no other network devices will be recognzied. Write down the Physical Address. This is another name for the MAC address.

It should be 12 characters 6 pairs of characters separated by hyphens. When you reset your D-Link DI router to the default settings, it reverted to WEP encryption and is using the default encryption key. Confirm that Shared Key is selected in the Authentication field. Confirm that Enabled is selected for the WEP setting.

Set the WEP Encryption field to the same level of protection 64Bit or Bit you assigned to the other computers and devices connected to your wireless network. It must be the same as assigned to the other computers and devices connected to your network. Enter the WEP encryption key you assigned to all the other computers and devices connected to your network. Enter the WPA-PSK encryption key that was assigned to the other computers and network adapters connected to your wireless network in the Passphrase field.

The status will change to "Connected" when you have successfully connected to the selected network. When you configured the computer attached to your router, you saved your Windows home networking information to a flash drive or to a removable media like a floppy disc.

In this step, you will use this saved information to configure the computers you're connecting to your home network. Note : If you are connecting computers running Windows 98 SE or Windows Me to your home network, you must use the flash drive or removable media to start the Network Setup Wizard. To configure Windows for home networking:. Insert the removable media into the appropriate type of drive on your computer. If you saved the information to a flash drive, insert the flash drive into an available USB port Download the complete instructions for easy printing.

Note : If your computer is running Windows XP, you can access the Network Setup Wizard without using the removable media saved when you connected your first computer to the router. Click Yes if a dialog box displays informing you that some network support files need to be installed.

Click Next when the "Before you continue" screen displays. Select This computer connects to the Internet through another computer on my network or through a residential gateway in the "Select a connection method" screen. Enter a description for this computer in the Computer description field. It should differentiate it from the other computers on your network. Enter a descriptive name in the Computer name field for this computer.

This is how it will be listed on your network. Enter the workgroup name for this computer. All the computers connected to this network must be assigned to the same workgroup.

Your computer will automatically be configured for your home network. Select Just finish the wizard; I don't need to run the wizard on other computers and click Next. You will use the same flash drive or removable media that you used on this computer to configure the remaining network computers. You don't need to create another setup disk. Because Microsoft will not provide security updates for these operating systems, we recommend that you upgrade to a supported version immediately to ensure the best possible performance.

Request Quote Order Now. Installing and configuring a wireless home network using a D-Link router Steps to create a D-Link wireless home network Creating a D-Link DI wireless home network requires six steps:. Open Internet Explorer or any other browser on your computer. The Verizon home page should display. If the Verizon home page does not display, refer to the D-Link router troubleshooting tips. After you have solved the problem, repeat this test.

Steps to create a D-Link Di wireless home network Before you begin setting up your wireless network be sure that you have completed each item on the checklist below. Review the wireless networking system requirements Review the factors to consider before installing your wireless network. Verify you have the required network adapters and accessories: D-Link Wireless USB adapterfor each desktop computer you are connecting to your network. Many newer computers are sold with wireless network adapters installed.

Steps to create a D-Link DI wireless home network Although you can set up a home network in earlier versions of Windows, you will find it significantly easier if the computer connected to the router is running Windows XP.

Click All Programs 3. Click Accessories Note : The name cannot contain spaces or special characters. Click Communications 5. Select Network Setup Wizard 6. Note : The name cannot contain spaces or special characters. Review the instructions for using the setup disk. Steps to create a D-Link DI wireless home network Security is an important issue when using a wireless home network.

Download the complete instructions for printing 2. Change your default router password Your D-Link router's default values of "admin" as the user name and no entry in the Password field are well-known to hackers. Select the Tools tab and click Admin. Enter a new Administrator user name in the Login Name field.

Enter a new password in the New Password field. Enter the password again in the Confirm Password field. Enable MAC Address filtering You can limit access to your home network to increase the security of the information stored on it. Select MAC Filters. Repeat Steps 5 - 7 for each computer you are allowing to access your home network. Select the Tools tab and click Misc.

Steps to create a D-Link DI wireless home network If you have additional computers you want to connect to your wireless network, please follow the directions below. If you don't have a wireless network adapter installed , connecting an additional computer will require two major steps: Configure Windows on the computers you are adding to the network so they have the correct components for home networking installed. Connect the other computers to your home network using Ethernet cable or wireless network adapters.

Create a completely wireless network by installing and configuring wireless network adapters for each computer. Create a combination network by connecting any computers that are close to your router with Ethernet cable. Then install wireless network adapters to connect notebook computers or computers that are farther away from the router. Software and specifications subject to change without notice. First, connect the power adapter to the receptor at the back panel of the DI and then plug the other end of the power adapter to a wall outlet or power strip.

Insert an Ethernet cable to LAN port 1 on the back panel of the DI and an available Ethernet port on the network adapter in the computer you will use to configure the DI Computers equipped with M2 LED — A solid light indicates that the unit is defective. This LED blinks during data transmission.

This LED blinks during wireless data transmission. When you have completed the steps in this Quick Installation Guide, your connected network should look similar to this:. Then press the. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Using a power supply with a different voltage rating will damage and void the warranty of this product.

DI Xtreme G 2.